Suspension Set for Short Span-manufacture,factory,supplier from China

(Total 24 Products for Suspension Set for Short Span)
1.The short span ADSS tension set is used for the installation of ADSS cable, includes ADSS guy grip, Galvanized thimble clevis and U shackle. 2. The structure of the short span ADSS guy grip is simple. When installation, the tubular structure formed by the legs of the pre-twisted wire can be naturally wound on the ADSS cable to produce a strong grip. The novel structure and unique design make the wire resistant to tension.
  Связаться сейчас
1.The short span ADSS guy grip is used for the installation of ADSS cable. 2. The structure of the short span ADSS guy grip is simple. When installation, the tubular structure formed by the legs of the pre-twisted wire can be naturally wound on the ADSS cable to produce a strong grip. The novel structure and unique design make the wire resistant to tension.
  Связаться сейчас
1.The short span ADSS helical guy grip is used for 10.6-11.6mm ADSS cable, with approximate length 940mm±30mm, or customize based on requirements of customers.2.The structure of the short span ADSS guy grip is simple installation, with strong grip once the tubular structure naturally wound on the ADSS cable. 3.The short span ADSS helical guy grip has reliable performance, made of aluminum-clad steel.Using tips1.Due to the special structure of guy grip, only be used once after being stressed, and cannot be reused. 2.The specification and model of the guy grip must be provided when an
  Связаться сейчас
ADSS suspension clamp material features: 1.Rubber clamp: It is composed of high-quality rubber and aluminum composite plate reinforcement, with chemical resistance, ozone resistance, weather resistance, aging resistance, high and low temperature performance, high strength and elasticity, and can withstand less pressure.
  Связаться сейчас
The small tension strain clamp is used for the span under 100 meters. It is a single-layer pre-twisted wire structure. It is designed for the small span installation of ADSS optical cable. It is simple and reliable, and the installation is convenient and quick.
  Связаться сейчас
Light short span tension set for ADSS cable diameter 11.0-12.0mm, tension strength 4KN, and max span 120 meters.The tension dead end guy grip is made of galvanized steel wire or aluminum-clad steel wire, and the inner wall of the pre-twisted wire is stuck with a layer of fine emery to increase friction.1.The short span ADSS tension set is used for the installation of ADSS cable, includes ADSS guy grip, Galvanized thimble clevis and U shackle. 2. The structure of the short span ADSS guy grip is simple.
  Связаться сейчас
Large span tension set for ADSS with advantages below:1.One-stop raw material supply completely2.Stable transmission, low loss3.Fast delivery, safe package, long service lifeSn Model No. Suitable for ADSS cable range(mm) 300M spanANZ 030/0940 8.6-9.4ANZ 030/1010 9.5-10.1ANZ 030/1070 10.2-10.7ANZ 030/1140 10.8-11.4ANZ 030/1220 11.5-12.2ANZ 030/1290 12.3-12.9ANZ 030/1370 13.0-13.7400M spanANZ 040/1220 11.5-12.2ANZ 040/1290 12.3-12.9ANZ 040/1370 13.0-13.7ANZ 040/1460 13.8-14.6ANZ 040/1550 14.7-15.5ANZ 040/1650 15.6-16
  Связаться сейчас
A compression type mid-span joint consists of the following parts:a. Aluminium alloy tube for aluminium alloy conductors.b.
  Связаться сейчас
Suspension set for ADSS features: 1.This product has uniform stress distribution and no stress concentration points, which can enhance the 2. Rigidity of the cable installation point without additional damage to the optical cable; The tangent clamp has a high dynamic stress bearing capacity, which can effectively lift and fix the line; 3.
  Связаться сейчас
Anchoring clamp pole clamp bracket is composed of CS14 cable bracket and ES 1500 suspension clamp. It is used on poles, in alignment or angle, different levels, also provide for hanging a public light bundle. The anchor pole clamp with stable quality, durable and long service life; neat and burr-free; simplify operation, convenient and easy to use.Features:1. Conductor range: 25-95sqmm2. Package:50 pieces3. Gross weight: 17 kg4. Dimension: 54×31×32cm5. Material: high strength alloy aluminum 
  Связаться сейчас
The performance advantages of ADSS suspension clamp set: (1).The stress of the pre-twisted suspension clamp is distributed in a larger area, which greatly reduces the influence of static stress on the optical cable, greatly improves the ability of the optical cable to withstand stress, and the ADSS suspension clamp has the same effect as the ADSS optical cable. Larger contact area, uniform stress distribution, no stress concentration points, and at the same time enhances the rigidity of the optical cable at the hanging point, which provides better protection.
  Связаться сейчас
Suspension string fittings include U-shaped screws, suspension clamps, pre-twisted wire protection lines, grounding drain wires and necessary connection fittings. The mechanical strength of the hanging string connection fittings is 70kN. The suspension clamp is a pre-twisted wire type, and the clamp body is made of aluminum alloy. The clamp body should be equipped with an EPDM rubber cushioning elastic pad. The allowable value of the drape angle at the outlet of the OPGW single drape clamp is not less than 15 degrees.
  Связаться сейчас
Tangent suspension clamp for FOR FIBER OPTIC CABLE ADSS Span 120m Diameter of ADSS cable:  11.8 ± 0.4 mm.  It is mainly used for the installation of optical cables on short-span linear pole towers below 150 meters, or pole towers with a rotation angle of less than 15 degrees.This product has rubber clamps and one-piece aluminum alloy casing (butterfly type).
  Связаться сейчас
ADSS optical cable suspension clamps are divided into several types according to the size of the line span, such as single-layer pre-twisted wire tangent clamps, single suspension clamps and double suspension clamps. The tangent clamp for ADSS optical cable is mainly used for the cable erection of 100m span, and the single-layer pre-twisted wire suspension clamp is mainly used for the erection of optical cable within the span of 100m-200m.Features: a. The suspension clamp has a larger contact area with the ADSS/OPGW optical cable, the stress is evenly distributed, and there is n
  Связаться сейчас
Features: 1. It has all the functions of a single suspension clamp.2.
  Связаться сейчас
ADSS Suspension Clamps Depending on the application and the fiber optic cable brand, we provide three types of suspension clamps: low tension, medium tension and high tension. Suspension clamps are mainly used on straight iron towers. They are the connection fittings for hanging ADSS optical cables on the towers. They are used to protect the optical cables from damage during erection and operation. The main technical parameters are the breaking force of the clamp (kN) and the cable.
  Связаться сейчас
Helical tension set ADSS long span with D shackle, Thimble clevis, helical dead end, protector rods. A dead-end is installed at each end of the cable length to attach to the structures. Two dead ends are used at angle changes of 30 degree or greater, either horizontal or vertical.
  Связаться сейчас
Fiber optic tangent used as cable suspension hardware simplest while the attitude of change, ether horizontal or vertical, is less than 15°.Armor grip suspesnion used for any span length with an angle change, either horizontal or vertical, less than 30°. Adss optical cable small pitch suspension clamps are especially used for cable erection within 100m pitch, and single-layer pre-twisted cord suspension clamps are specially used for optical cable erection inside 100m~200m pitch.
  Связаться сейчас
Suspension clamps for optical cables are made of real materials, with stable performance and long service life. Composed of insulating clamps and connecting buckles, the stress distribution is even, there is no concentrated point, it can enhance the rigidity of the cable installation point, and the protection performance of the optical cable is good. It has a larger contact area with the optical cable and is equipped with flexible rubber clamps to enhance self-damping and reduce wear.
  Связаться сейчас
100M span ADSS cable tension set is used to connect to the pole and tower in the erection of wires and optical cables.
  Связаться сейчас
The stay rod is called stay set as well, it is a component used to connect the stay wire to the ground anchor.The stay rod are made of Q235B steel, hot dip galvanized surface treatment which used for LV & MV stay rod assembly installation. Both bow type and tubular type we can supply, the tubular type stay rods MV & LV(M16×1830mm; M20×2440mm)exported to most of African countries. Features:1. Material: high strength carbon steel2. Application: for stay rod assembly3. Dimension: M20×2440mm4. Finish: hot dip galvanized 
  Связаться сейчас
Features: a. Even stress distribution, no stress concentration point, can well protect the optical cable. b. Under the premise of not exceeding the lateral compression strength of the optical cable, it has a greater grip on the optical cable and can withstand greater tension. c. The grip strength of the optical cable is not less than: 95% of the ultimate tensile strength (UTS) of the optical cable, which is fully suitable for the needs of optical cable erectionProduct composition diagramProduct technical specification sheet:  Sn Model No.
  Связаться сейчас
The preformed armor rod is used to protect the wire from vibration, clamping stress, friction, arc and all other external damage. The armor rod section protection wire can protect the wire from arc, friction or other damage on the short-span line when the wire vibration is not serious.
  Связаться сейчас
ADSS preformed tension set , single-layer twisted wire can be used below 200 meters; high-tension strain clamp, double-layer twisted wire can be used for spans above 200 meters. The technical parameters required for the quotation are: the diameter of the applied wire, the range of use, the tensile force and so on.Composition: inner rods, helical guy grip, thimble clevis, U shackle, extension ring, etc.Product parameter According to different needs, the configuration intensity is 70kNSn Model No.
  Связаться сейчас
Relate News
Characteristics1) low wear: because of the big bar and short good sized clench conductor, the cord is tough to slide, the wear and tear might be minimum.2) save you loosening: the preformed has preserving elasticity, it make sure it not unfastened in long time;3) good corrosion-resistance characteristics: after antirust processing, the cord ensuring the sturdy corrosion resistance;4) clean set up: no unique equipment, the hand can installation quick and easy in locale, one person can finish.5) installation first-class warranty: no need the special training; it is able to be inspected by using
Features of Transmission Line OPGW Tension SetA. the stress distribution is uniform and there can be no pressure focus factor, that can protect the optical cable well.B. beneath the concept of now not exceeding the lateral compression electricity of the optical cable, it has a greater grip at the optical cable and can resist more tension.C. the grip energy of the optical cable isn't always much less than: 90 5% of the last tensile energy (uts) of the optical cable, that is clearly suitable for the wishes of optical cable erection.
The preformed suspension clamp is used for the connection of various wires such as ADSS optical cable and OPGW optical cable in the linear pole tower.
Wonderful anti-pressure ability, accurate brief-circuit current ability ;Match with ordinary floor cord l undertake stainless-steel pipe production generation, the pipe is full of water-blocking off compounds, the application version can efficaciously protect the optical fiber ;Using stainless steel tube production technology, the tube filled with water-blocking compounds, can effectively protect the optical fiber;The utility model has the dual functions of a ground wire and a communication optical cable, and avoids the huge cost of repeated erection and maintenance;It is installed on the top
Mini-Bracket Mini Brackets are used for short and medium spans of ADSS fiber optic cable as well as Aerial Drop cables. Mini Brackets are sized to fit specific ADSS diameters. Standard Mini Brackets are employed with fitted bushings to provide a good support/groove fit and to prevent the support from damaging the cable. The bolted supports are supplied with aluminum captive bolts to simplify installation with no loose parts.
Optical cable joint box, ADSS optical cable joint box, OPGW optical cable joint box, OPPC optical cable joint box Uses: Widely used in ADSS, OPGW special optical cable joints and the junction of different optical cables, and play a role in protecting optical cable joints. Features: 1.The metal splice box is made of aluminum alloy casting, which is especially suitable for the protection of optical cable joints under high-voltage electric fields. 2.The metal splice box overcomes the weakness of the plastic splice box, which is poor in anti-aging ability and short life under t
Spiral preformed tension clamp and ADSS single-layer tension clamp have similar functions as tension clamp. Spiral preformed tension clamps are mainly used for poles and towers with short spans of 50 to 200 meters, such as corners, tensions, and terminals.
Characteristics of PET Packing Tape(1) Sturdy tensile energy, not most effective has the tensile power of metal strip, but additionally has the ductility of effect resistance, that may ensure the transportation safety of merchandise. (2) Small elongation, elongation is most effective one-sixth of the polypropylene belt, can hold the anxiety for a long time. (3)Robust temperature resistance, melting point of 260 stages, a hundred and twenty degrees under the use of non-deformation. (4) Top security, no metal rust pollutants of the sure gadgets, vivid shade can be used for referen
1.1 puncture structure, easy installation, no need to peel insulated wire; 1.2 moment nut, constant puncture pressure, ensure good electrical connection without damaging wire; 1.3 self sealing structure, moisture proof, water proof, corrosion proof, extend The service life of insulated conductors and clamps 1.4 use special contact blade, suitable for copper (aluminum) Butt joint and copper-aluminum transition 1.5 electrical contact resistance is small, contact resistance is less than 1.1 times of resistance of equal length branch wire, dL/T765.1-2001 standard 1.6 speci
The pole clamp is suitable for connecting the anxiety suspension clamp and the electric pole. A big quantity of various varieties of hoops are wanted in overhead strains or whilst putting in pole accessories. it's miles especially easy to put in hoops on equal-diameter poles, just recognize the unique diameter. while installing a hoop on a tapered pole, if the hoop size is simply too massive, you want to insert iron pieces internal; if the ring is too small, the hoop and the telegraph pole cannot in shape together.
Power fittings are accessories made of metal materials that are often used for power output. These accessories are of various types, and the shape and size of each part are different, but they play a very important role. Even very small parts will be indispensable, helping people to output electricity. Some of our common metal rings or metal clips, as well as connecting rings that can be connected to metal pipes, belong to the category of fittings.
Wires mainly include bare wires, electromagnetic wires, insulated wires, power cables, communication cables and optical cables for electrical appliances. Electric cable refers to the materials used for power, communication and related transmission purposes. There is no strict boundary between "wire" and "cable".