Tension insulators are used for transmission and distribution lines and communication lines, broadcast line terminals, corners or large-span poles, The balance pole is subjected to tensile stress. When in use, the wire and the pull wire pass through the hole and slot, and the tension wire is used for insulation and connection.Features:1. Material: high strength carbon steel2. Application: for stay rod assembly3. Dimension: M16×1830mm4. Finish: hot dip galvanized
Связаться сейчас
The stay rods is for 40kN LV stays, the diameter of rods is M16, each element/material stay rod, stay base plate, guy grip, top make off, thimble are easy for assembly.A drawing of stay bows complete with thimble:
Связаться сейчас
Stay guy grips are used for stay rod, stay insulator and pole top attachment.
Связаться сейчас
Stay rod is used for sustaining the mechanical load of the stay wires.The stay bow are made of Q235B steel, hot dip galvanized surface treatment which used for LV & MV stay rod assembly installation. Both bow type and tubular type we can supply, the tubular type stay rods MV & LV(M16×1830mm; M20×2440mm)exported to most of African countries.Features:1. Material: high strength carbon steel2. Application: for stay rod assembly3. Dimension: 16mm4. Finish: hot dip galvanized
Связаться сейчас
The strength distribution cable is equipped with rubber pads to offer anti-put on characteristic. the state line is not geared up with rubber pads and isn't sandblasted. due to the fact that there are rubber pads to provide buffering around the cord, the abrasion of the touch floor between the wire and the insulator is prevented. therefore, the energy distribution cable can provide better safety to the wires, and the installation is less difficult and faster.
Связаться сейчас
The stay rod is called stay set as well, it is a component used to connect the stay wire to the ground anchor.The stay rod are made of Q235B steel, hot dip galvanized surface treatment which used for LV & MV stay rod assembly installation. Both bow type and tubular type we can supply, the tubular type stay rods MV & LV(M16×1830mm; M20×2440mm)exported to most of African countries. Features:1. Material: high strength carbon steel2. Application: for stay rod assembly3. Dimension: M20×2440mm4. Finish: hot dip galvanized
Связаться сейчас
Stay grips dead ends is the preformed wire type, minimum length is 600mm and finish is galvanized. Thimbles is used with guy grips to support wires through the stay rod eye. A combination of guy grips and pole top make offs is used.Installation image:
Связаться сейчас
The power distribution cable tie is equipped with rubber pads to provide anti-wear function. The state line is not equipped with rubber pads and is not sandblasted. Since there are rubber pads to provide buffering around the wire, the abrasion of the contact surface between the wire and the insulator is avoided. Therefore, the power distribution cable can provide better protection to the wires, and the installation is easier and faster.
Связаться сейчас
1.Polymer Insulator Character:1.1high mechanical strength;1.2Good performance of hydrophobicity and anti-pollution;1.3 Excellent electrical Performance;1.4 small volume and lightweight. Type of productsOur products cover 10KV-1100KV high-voltage and extra-high voltage hollow ceramic insulators.Which include GIS outlet line insulator shellSF6 circuit breaker insulator shellCombined current and potential transformer insulator shell.capacitor insulator shellcable terminal insulator shellarrester insulator shell and solid pillar insulatorfuse protector insulatortank capacitor outlet line casi
Связаться сейчас
The stay plates are made of Q235B steel, hot dip galvanized surface treatment which used for LV & MV stay rod assembly installation. Both bow type and tubular type we can supply, the tubular type stay rods MV & LV(M16×1830mm; M20×2440mm)exported to most of African countries.Features:1. Material: high strength carbon steel2. Application: for stay rod assembly3. Dimension: 450×450×6mm×22mm hole diameter4. Finish: hot dip galvanized
Связаться сейчас
1.The 100M span ADSS guy grip is used for the installation of ADSS cable. 2.The structure of the 100M span ADSS guy grip is simple, has sandy cover, excellent tensile properties, good resistance to oxidation and corrosive agents.Using tips:1.Due to the special structure of guy grip, only be used once after being stressed, and cannot be reused. 2.The specification and model of the guy grip must be provided when an inquiry. 3.It is not allowed to overlap on the guy grip, but it is allowed to overlap the conductors& cables.4.The lay direction between the guy grip and the conduc
Связаться сейчас
1. The twisting direction of the steel stranded wire and the matching preformed guy grip needs to be the same, and the tensile strength of the galvanized steel wire is 1370N/mm2-1470N/mm2. 2. The white corundum used to increase the friction between the pre-twisted wire and the surface should meet the requirements of GB/T 2479.3. The surface of the preformed guy grip should be smooth and free of defects such as cracks, folds and scars.4. The size and tolerance of the pre-twisted wire The size of the pre-twisted wire should meet the requirements of the design d
Связаться сейчас
1.The short span ADSS guy grip is used for the installation of ADSS cable. 2. The structure of the short span ADSS guy grip is simple. When installation, the tubular structure formed by the legs of the pre-twisted wire can be naturally wound on the ADSS cable to produce a strong grip. The novel structure and unique design make the wire resistant to tension.
Связаться сейчас
The energy distribution top tie can be used to fix naked or insulated wires inside the top grooves of pin insulators and submit insulators of the power distribution device.
Связаться сейчас
The adaptor socket clevis W-7B is mainly used to connect the suspension clamp and the insulator string, and cooperate with other accessories to connect the wires and insulate. ALL WELL W-7B has high mechanical strength, is not easy to produce cracks, has good structural stability, the product is not easy to age, and the surface is polished and polished without burrs. In the transmission line, the bowl head hanging board W-7B plays the role of hanging the insulator string and the suspension clamp, and bears greater working stress.
Связаться сейчас
The socket clevis W-7A is the connection fitting in the power fittings. In the transmission line, the Wantou Hanging Board W-7A plays the role of suspending the insulator string and the suspension clamp, and bears greater working stress. Its safety performance is very important to the transmission line. The Wantou Hanging Board is in the construction of the power grid.
Связаться сейчас
Dimensions:Height: 545±5mm.Min Dry Aring Distance:350mm. Min Creepage Distance:900mmDiameter Of The Rod:Φ17mm.Coupling Dimensions: Single Ear/ Binaural.Number Of Sheds: 8. Raw Materials:1.End-Fitting:1.1Material: Socket: Cast Iron Or Cast Steel, Hot Dip Galvanized. Ball: Forged Steel, Hot Dip Galvanized.1.2 Minimum Thickness Of The Galvanization:86um.2.Core:2.1 Material: Epoxy& Glass Fiber, Acid-Resistant Type.2.2 Diamter:Φ17mm.3.
Связаться сейчас
Transmission line fitting socket tongue is suitable for connecting suspension insulator strings between overhead power lines and substations. In the transmission line, the bowl head hanging plate plays the role of hanging the insulator string and the suspension clamp, and bears greater working stress.Features: 1. Cast, hot-dip galvanized.2. Connection mark 16; 20; 24.3. Equipped with W pins, the pins are stainless steel or bronze.
Связаться сейчас
Galvanized steel pole top make off is generally double wrapped around the pole. 3 strands plus king wire and effective 7 strand stay length for dead end attachment. top to facilitate termination of the stay strand that firms the pole on the earth.Features:1. Material: galvanized steel wire2. Application: for stay rod assembly3. Dimension: 1750 overall length mm4. Finish: hot dip galvanized5. Stay wire diameter: 12mm6. Tensile strength” 63kNProduction drawing: Installation image:
Связаться сейчас
1.The 100M span ADSS guy grip is used for the installation of ADSS cable. 2.The structure of the 100M span ADSS guy grip is simple, has sandy cover, excellent tensile properties, good resistance to oxidation and corrosive agents.Using tips:1.Due to the special structure of guy grip, only be used once after being stressed, and cannot be reused. 2.The specification and model of the guy grip must be provided when an inquiry. 3.It is not allowed to overlap on the guy grip, but it is allowed to overlap the conductors& cables.4.The lay direction between the guy grip and the conduc
Связаться сейчас
The structure of the preformed strain clamp is simple, and its pre-twisted wire legs are twisted to form an empty tube, and the rear part is a pre-formed twisted ring. The empty tube formed by the legs of the pre-twisted wire can generate a strong grip when it is wound on the wire, and the twisted loop is used to fix the insulator.
Связаться сейчас
The thimble is made of carbon steel Q235B, and the surface is hot-dip galvanized, smooth and flat, without any defects such as missing plating, zinc particles, bubbles, and cracks. The galvanized layer has sufficient adhesion strength during normal application.
Связаться сейчас
The top tie are all designed in a spiral structure and include aluminum-clad steel wires. the central part of the energy distribution cable is fashioned in the factory, and its form may be matched with diverse insulators and wires.
Связаться сейчас
The WS-type bowl head hanging plate produced by our company has the characteristics of oxidation resistance, corrosion resistance, and durability. It is suitable for the connection between the insulator string and the fittings, the line clamp and the insulator string, and the lightning protection wire and the pole tower. The main body is made of malleable cast iron, hot-dip galvanized, oxidation-resistant and corrosion-resistant.
Связаться сейчас