The plastic fisher screw wall plug is made of high-quality PE material, which has strong fixation and is not easy to rotate. A variety of sizes are available for a wide range of applications. Corrosion-resistant, high-density polyethylene has rigidity, hardness and mechanical strength.
Связаться сейчас
The c-type hook is used as an accessory for outdoor or indoor wall fiber access. The main purpose is to form an anchor on the wall for the erection and support of the fiber.
Связаться сейчас
FTTH drop cable screw eye is a supporting device that is directly screwed to a wooden wall or fixed to a brick-concrete wall with an expansion tube to connect and fix the S fixing member. Cement walls need to be used with expansion plugs.The expansion plug is used in conjunction with the ring hook. It is used as an optical fiber access accessory on the cement wall.
Связаться сейчас
FTTH drop cable fisher screw eye is installed on the bracket, used to connect and fix the S fixing piece. The expansion plug is used in conjunction with the ring hook. It is used as an optical fiber access accessory on the cement wall.
Связаться сейчас
-Impact: No damage on dropping from altitude ≥ 6m to a hard floor-Vibration: Resistance against vibration of standard sine wave, frequency: 20 Hz, Amplitude: ≥ 5mm, duration: 0.5 hour-Material: durable PVC-Color: light gray or white -Temperature: -10°C up to +70°C-Humidity: Up to 100 %.Specification required for different cable diameter ranges:No.ItemUnitSpecification required for different cable diameter ranges (mm)4.0 ~ 6.346.35~ 8.288.5 ~ 11.711.71 ~ 14.314.31 ~ 19.31.1Diametermm9.8-10.39.8-10.310.8-11.312.0-12.912.0-12.91.2Length mm125012501300135016501.3Gripping section lengthmm
Связаться сейчас
The medium and high tension strain clamps are composed of a double-layer twisted wire structure. The tensile inner twisted wire is made of galvanized steel wire or aluminum-clad steel wire. The inner wall of the pre-twisted wire is stuck with a layer of fine emery to increase friction. The pre-twisted wire is preformed into four sub-bundles during processing to avoid installation errors and facilitate quick installation. The ends of the pre-twisted wires are bent radially outward to avoid squeezing and damaging the optical cable.
Связаться сейчас
The c type hook clamp is used as an accessory for outdoor or indoor wall fiber access. The main purpose is to form an anchor on the wall for the erection and support of the fiber. The hanging part rotates more than 180 degrees, so the wire It can only fall off manually, and the wire will not be unhooked even in a strong wind environment.
Связаться сейчас
Cable wall mounted anchoring clamp with ScrewsMaterial: hot dip galvanized steelOur clamp anchoring bracket with the advantages below:1. Reduce cable maintenance expenses, avoid frequent repairs, save operating costs, and users get a better experience. 2. The FTTH technology has been widely used, the construction speed is also very fast, and the technical risk is low.3. It provides a stable and reliable guarantee for fiber to the home, and the efficiency of network usage is improved.
Связаться сейчас
The TC insert ring is made of Magang, which has high strength and toughness, high vibration damping and good elongation. Malleable iron generally refers to malleable cast iron, cast iron with a certain chemical composition into a white blank, and then annealed cast iron, which has higher strength, plasticity and impact toughness, and can partially replace carbon steel. Technical characteristics:Model No.: TC-05Bolt size: M14Tension strength: 50KN
Связаться сейчас
ADSS terminating helix dead end is made of aluminum-clad steel wire, and the pre-twisted wire is preformed into a bundle during processing, and a firm layer of emery is glued to the inner wall to increase the grip of the tension clamp under the condition of reducing the side pressure on the optical cable.
Связаться сейчас
Preformed inner protection line rods:The material is aluminum-clad steel wire, which is the same material as all the aluminum-clad steel wires of OPPC cable. The inner wall of the protector rods is glued with a layer of gold steel sand through a high-strength polymer water-soluble environmentally friendly adhesive to increase the friction with the optical cable. The rods is preformed into four sub-bundles during production, which is convenient for quick installation.
Связаться сейчас
Medium and large tension set are composed of a double-layer twisted wire structure. The tension inner rods is made of galvanized steel wire or aluminum-clad steel wire, and the inner wall of the pre-stranded wire is stuck with a layer of fine emery to increase friction. The inner rods includes 4 groups, during processing in the factory to avoid installation errors and facilitate quick installation. The ends of the pre-twisted wires are bent radially outward to avoid squeezing and damaging the optical cable.
Связаться сейчас
Light short span tension set for ADSS cable diameter 11.0-12.0mm, tension strength 4KN, and max span 120 meters.The tension dead end guy grip is made of galvanized steel wire or aluminum-clad steel wire, and the inner wall of the pre-twisted wire is stuck with a layer of fine emery to increase friction.1.The short span ADSS tension set is used for the installation of ADSS cable, includes ADSS guy grip, Galvanized thimble clevis and U shackle. 2. The structure of the short span ADSS guy grip is simple.
Связаться сейчас
1. The twisting direction of the steel stranded wire and the matching preformed guy grip needs to be the same, and the tensile strength of the galvanized steel wire is 1370N/mm2-1470N/mm2. 2. The white corundum used to increase the friction between the pre-twisted wire and the surface should meet the requirements of GB/T 2479.3. The surface of the preformed guy grip should be smooth and free of defects such as cracks, folds and scars.4. The size and tolerance of the pre-twisted wire The size of the pre-twisted wire should meet the requirements of the design d
Связаться сейчас
The repair sleeve comprises of two pieces with a provision of seat for sliding of the keeper piece.
Связаться сейчас
1. Material: high-quality steel, good electrical conductivity, fast heat dissipation and high temperature resistance.2. Treatment: Advanced technology, hot-forged forming without burrs, smooth surface.3. Strict quality inspection, factory direct sales, quality assurance.Model No.: QH-7Tension strength: 70KNThe main dimensions of the PH extension link meets the requirements of the following figure and table:The meanings of letters and numbers in the models in the table are: number--nominal failure load mark.
Связаться сейчас
The strength distribution cable is equipped with rubber pads to offer anti-put on characteristic. the state line is not geared up with rubber pads and isn't sandblasted. due to the fact that there are rubber pads to provide buffering around the cord, the abrasion of the touch floor between the wire and the insulator is prevented. therefore, the energy distribution cable can provide better safety to the wires, and the installation is less difficult and faster.
Связаться сейчас
The top tie are all designed in a spiral structure and include aluminum-clad steel wires. the central part of the energy distribution cable is fashioned in the factory, and its form may be matched with diverse insulators and wires.
Связаться сейчас
Tie rods is supplied with four full nuts. The material of the rods is steel, strength grade designation 4.6 and meet the requirements for mechanical properties.
Связаться сейчас
The pole clamp is suitable for connecting the tension suspension clamp and the electric pole. Features: 1. Product manufacturing is strictly controlled and meets production standards. 2.The surface of the product has no burrs and is relatively smooth. 3. Support customization of a variety of special-shaped productsThe hoop device is composed of a hoop plate, a wing plate, a tie rib plate, a bolt and an inner liner. An embedded hoop, which is formed by joining the left and right halves of the hoop.
Связаться сейчас
PAL1000 aluminum alloy optical cable insulation strain clamp is a product suitable for overhead insulated conductors. The product is used for cable pull, aluminum alloy body material, PA66 insulation core, stainless steel wire rope, and the product process is die-casting. The high-quality aluminum alloy material has strong corrosion resistance and is not easy to rust and age. The appearance is neat and tidy, and the unique design can well protect the cable.Features:1. Material: high strength aluminum alloy.
Связаться сейчас
The transformer bracing cross arm is the cross of dimension of 550x50x50x6mm。The cross arm is hot dipped galvanized.All steel members and other parts of fabricated material as delivered is free of warps, local deformation.Bending of flat strap is carried out cold.About surface treatment:All galvanizing is carried out by the hot dip process. The zinc coating is smooth, continuous and uniform. It is free from acid spot and shall not scale, blister or be removable by handling or packing.
Связаться сейчас
The protective rod is divided into FYB and FYH types.
Связаться сейчас
ADSS optical cable suspension clamp components: 1.Aluminum clamp:made of corrosion-resistant aluminum alloy pressure casting, the aluminum alloy has stable chemical properties, good atmospheric corrosion resistance and good mechanical properties. 2.Rubber clamp:Composed of high-quality rubber and center reinforcement, it has the properties of ozone resistance, chemical resistance, weather resistance, high and low temperature performance, high strength and elasticity, and small compression deformation. 3.Bolts, flat washers, spring washers, nuts, closed pins, U-shaped hanging rin
Связаться сейчас