The OPGW grounding clamp consists of a section of aluminum alloy wire, an aluminum alloy clamp (connected to the OPGW optical cable), and all-aluminum terminal blocks (connected to the main material of the iron tower).
Связаться сейчас
ADSS/OPGW anti-vibration hammer protective wire is a protective wire used to suppress the vibration of conductors and ground wires on overhead power lines.
Связаться сейчас
The grounding clamp is mainly used for the grounding of the OPGW optical cable to provide a path for short-circuit current. The grounding clamp consists of a grounding wire, a set of aluminum alloy parallel groove clamps (connecting OPGW optical cable and grounding wire) and a terminal (connecting to the iron tower). Usually, one terminal tower and linear tower are equipped, and two connecting towers are equipped.
Связаться сейчас
Composition: inner stranded wire, outer stranded wire, embedded ring, PD type hanging plate, U type hanging ring, etc. Purpose: To withstand full tension. Connect the optical fiber composite ground wire to the terminal, tensile strength (rotation angle greater than 25°) or the optical cable connection pole. Features: a. The stress distribution is uniform and there is no stress concentration point, which can protect the optical cable well. b.
Связаться сейчас
Optical cable clamps FTTH optical fiber accessories 201 stainless steel + nylon material, customized various optical cable overhead fittings, FTTH optical fiber into the home, optical fiber into the community accessories, etc.The fiber is squeezed through the sheet and the sheet, and the fiber is squeezed in the middle to complete the wiring function. The main function is to prevent the wire body from bending and protect the wire body, and the locking position can be moved quickly and simply. It is easy to use, put the optical fiber into the slot, install the pull piece, and tighten
Связаться сейчас
The protective wire can avoid damage caused by the aluminum clamp of the anti-vibration hammer directly clamped on the 0PGW optical cable, and has a good protective effect on the optical cable. The factors that cause vibration include span, tension, wind speed, wind direction, ground wire and cable structure size, etc. Features: a. Using a unique design, its basic principle is to dynamically absorb energy, its frequency coverage is 6Hz-150Hz, and there are four resonance frequencies in this range, which can meet the needs of various types of OPGW, and has a very effective v
Связаться сейчас
Direct supply of stainless steel S-type fixing parts, suitable for installation of optical fiber broadband FTTH accessoriesThe fiber is squeezed through the sheet and the sheet, and the fiber is squeezed in the middle to complete the wiring function. The main function is to prevent the wire body from bending and protect the wire body, and the locking position can be moved quickly and simply. It is easy to use, put the optical fiber into the slot, install the pull piece, and tighten it.For self-riding butterfly optical cable 2*5mmDimension: 210×15mmDrawing:Installation image:
Связаться сейчас
Applications 1.Tensile clamps for OPGW optical cables are mainly used to connect optical cables with a breaking strength of 160kN and below to tensile poles, corner poles and terminal poles. The complete set of OPGW optical cable strain clamp includes outer pre-twisted wires, inner pre-twisted wires, supporting connectors and grounding wires.
Связаться сейчас
Fiber to the home FTTH accessories, S-type fixing cable clamp are composed of stainless steel wire and flame-retardant ABS plastic parts. It is used to bind the self-supporting drop-in optical cable suspension wire and hang the optical cable on the supporting device.The S type cable clamp is used to bind the self-supporting leather cable suspension wire and hang the optical cable on the supporting device, be steadily strengthened and tightened. There are several colors can be chosen: gray, black, white.Instruction: Wrap the 2-5mm optical brazing wire in the cylindrical groove of
Связаться сейчас
OPGW Optical Cable Tension Fitting StringFeatures:a. Even stress distribution, no stress concentration point, can well protect the optical cable.b. Under the premise of not exceeding the lateral compression strength of the optical cable, it has a greater grip on the optical cable and can withstand greater tension.c. The grip strength of the optical cable is not less than: 95% of the ultimate tensile strength (UTS) of the optical cable, which is completely suitable for the needs of optical cable erection. Schematic diagram of product composition:Technical specification sheet
Связаться сейчас
ADSS optical cable rubber rod down-lead clamp is made of corrosion-resistant, weather-resistant EPDM rubber. It is used for fixing ADSS on the pole tower, suitable for different cable diameters, convenient and reliable installation, and wide adjustable range.1.Function: Fix the optical cable leading up or down on the pole tower to prevent it from shaking and avoid the optical cable from wearing. 2.Condition: The fiber optic cable line and the continuous poles on the first and end poles. 3.Method: usually install one every 1.5 meters.Technical specification table:
Связаться сейчас
The second damper can be used for OPGW tension tower vibration dampers if necessary. Tension assembly is used for OPGW cable route's fixing and anchor shackling. Usually be installed on the terminal tower, tight tension tower and intersection angle tower.OPGW tension tower vibration dampers installation image:
Связаться сейчас
FR anti-vibration hammer, optical cable anti-vibration hammer, pre-twisted anti-vibration hardware Product usage: Reduce the vibration amplitude of the wire. Applicable conductor: steel core aluminum stranded wire Process: Hot-dip galvanizingFeatures: 1.Tuning fork structure: The anti-vibration hammer adopts a special tuning fork structure, which can generate four resonant frequencies, which greatly covers the vibration frequency range of the cable in reality. 2.Real materials: The hammer head is gray cast iron, painted.
Связаться сейчас
ADSS spiral vibration rods is mainly used on overhead lines to eliminate or reduce the vibration of wires and optical cables under the action of laminar wind to clamp the damage to the fittings and the outer sheath of the optical cable. The anti-vibration whip is not only suitable for ADSS optical cables, but also suitable for OPGW optical cables and power transmission cables.Structural features: 1. The structure is simple, the installation is convenient, the maintenance is easy, and the installation position is not limited. 2. The spiral vibration isolator includ
Связаться сейчас
ADSS optical cable tower with down-lead clamp, optical cable clamp, fixed optical cable clamp.The lead-down clamp is used to lead down the optical cable and fix the optical cable when it is jumpered, which improves the mechanical performance of the clamp. It is mainly used for the communication line of the newly built overhead high-voltage power transmission system of 35kv and above. The stainless steel tube and cable core stranding design is reasonable, and the optical fiber is redundant.
Связаться сейчас
FTTH fiber-in-the-home clamp, designed for hanging, flat optical cable. The clamp is very easy to install and does not require other tools. It can be easily installed on the hanging bracket by manually adjusting the hanging ring. The clamp is equipped with perforated gaskets, which can increase the load when the optical cable is dropped.
Связаться сейчас
Power equipment optical cable communication 4D type protective hardware anti-vibration hammer with armor rod. Features: Due to the use of hammers with different sizes and masses, the response frequency range of traditional shock-proof hammers is expanded. Because the shapes of large and small hammers and hooks have no edges and corners, corona is reduced. In addition, the use of aluminum alloy for the hook can also reduce the energy loss of the wire.
Связаться сейчас
ADSS optical cable small pitch suspension clamps are mainly used for cable erection within 100m pitch, and single-layer pre-twisted wire suspension clamps are mainly used for optical cable erection within 100m~200m pitch.
Связаться сейчас
JBL series special-shaped parallel groove clamps are used for the connection of small and medium cross-section aluminum stranded wire or steel core aluminum stranded wire and the steel stranded wire of overhead lightning protection wire at a position that does not bear tension.
Связаться сейчас
Hot-rolled steel strip or steel plate is used as raw material and rolled into a product by a cold rolling mill at room temperature.1.Standard: GB4239-84 2.Features: good surface quality and smooth 3.Billet: Hot-rolled stainless steel strip4.The thickness of cold-rolled steel strip is 0.1~3mm, such as: 0.30, 0.40, 0.50, 0.60, 0.70, 0.80, 0.90, 1.00, 1.20, 1.50, 2.00, 2.50, 3.00mm.The surplus cable rack is used to suspend and fix the surplus OPGW optical cable and ADSS optical cable on the tower in the overhead line for maintenance and inspection. 1.The remaining cable rack for po
Связаться сейчас
The optical cable remaining rack is used to place the surplus optical cable when the optical cable is connected. Its main technical parameter is the diameter of the remaining cable rack (mm). Generally, each connector box is equipped with a remaining cable rack. Reference data: Cable storage diameter (mm): 600mm Weight (kg): 3.8 Material: galvanized steelPurpose: It is used to place the surplus optical cable when the optical cable is connected.
Связаться сейчас
The Optical fiber tension guy grip for ADSS with the technical specifications below: Brand: ALL WELLModel No.: ANZCustomized processing: yes Span: 300M -500MCable diameter: 16mm Tension strength: 70KNGripping force: 40-60kNSn Model No. Suitable for ADSS cable range(mm) 300M spanANZ 030/0940 8.6-9.4ANZ 030/1010 9.5-10.1ANZ 030/1070 10.2-10.7ANZ 030/1140 10.8-11.4ANZ 030/1220 11.5-12.2ANZ 030/1290 12.3-12.9ANZ 030/1370 13.0-13.7400M spanANZ 040/1220 11.5-12.2ANZ 040/1290 12.3-12.9ANZ 040/1370 13.0-13.7ANZ 040/1460&nb
Связаться сейчас
The surplus cable rack is used to suspend and fix the surplus OPGW optical cable and ADSS optical cable on the tower in the overhead line for maintenance and inspection. 1.The remaining cable rack for poles is fixed on the poles by two sets of steel band hoops 2. The remaining cable frame for the tower is fixed on the iron tower angle steel by two sets of right-angle splints.Purpose: It is used to place the surplus optical cable when the optical cable is connected.
Связаться сейчас
ODWAC, FTTH Self-supporting butterfly-shaped lead-in optical fiber cable installation accessories, stainless steel clamps, optical cable fixing partsThe fiber is squeezed through the sheet and the sheet, and the fiber is squeezed in the middle to complete the wiring function. The main function is to prevent the wire body from bending and protect the wire body, and the locking position can be moved quickly and simply. It is easy to use, put the optical fiber into the slot, install the pull piece, and tighten it.For self-riding butterfly optical cable 2*6mmBreaking load: 1 kNInstallati
Связаться сейчас