Nylon cable ties are made of UL-approved nylon-66 (Nylon 66) by injection molding, with a fire rating of 94V-2. They have good acid resistance, corrosion resistance, insulation, resistance to aging, and strong endurance. The operating temperature is -20°C to +80°C (normal nylon 66). Nylon cable ties have high tensile strength, impact resistance, and strong acid and alkali resistance.
Связаться сейчас
The cable tie is able to loop and lock fully. Extra tie material left past the lock to prevent pull through. Self-locking design for fast and secure installation provided.The cable tie have maximum diameter capable of bundling two to four service wires and cables with cross-section in the range of 4-25mm2.
Связаться сейчас
The energy distribution top tie can be used to fix naked or insulated wires inside the top grooves of pin insulators and submit insulators of the power distribution device.
Связаться сейчас
The preformed top tie are all designed in a spiral structure and consist of two aluminum-clad steel wires. The central part of the power distribution cable is formed in the factory, and its shape can be matched with various insulators and wires.
Связаться сейчас
The power distribution cable tie is equipped with rubber pads to provide anti-wear function. The state line is not equipped with rubber pads and is not sandblasted. Since there are rubber pads to provide buffering around the wire, the abrasion of the contact surface between the wire and the insulator is avoided. Therefore, the power distribution cable can provide better protection to the wires, and the installation is easier and faster.
Связаться сейчас
The power distribution top tie can be used to fix bare or insulated wires in the top grooves of pin insulators and post insulators of the power distribution system.
Связаться сейчас
The tie strap is used for tying 11kV or 33kV cross-arms to poles. There are steel galvanized bolts and nuts assembled. All ferrous part is made in hot dip galvanized.
Связаться сейчас
The top tie are all designed in a spiral structure and include aluminum-clad steel wires. the central part of the energy distribution cable is fashioned in the factory, and its form may be matched with diverse insulators and wires.
Связаться сейчас
The JJ-3 insulation piercing clamp has a main line cross-section of 16-95mm, a branch cross-section of 1.5-10mm, an applicable voltage of 1KV, and a nominal current carrying capacity of 138. It has the characteristics of long service life, high conductivity, and firm wiring. Features:1. Simple installation: puncture structure, no need to strip the wire, torque nut, constant puncture pressure. 2. Thickened shell: Nylon material is used to ensure that it can bear enough pressure.3.
Связаться сейчас
The JJ-3 insulation piercing clamp has a main line cross-section of 16-95mm, a branch cross-section of 1.5-10mm, an applicable voltage of 1KV, and a nominal current carrying capacity of 138. It has the characteristics of long service life, high conductivity, and firm wiring.Features: 1. Simple installation: puncture structure, no need to strip the wire, torque nut, constant puncture pressure.2. Thickened shell: Nylon material is used to ensure that it can bear enough pressure.3.
Связаться сейчас
Self-supporting optical cable clamp ADSS optical cable tension clamp is a commonly used ADSS optical cable clamp. The main body material is PA66, stainless steel wire rope, injection molding process, widely used in communication engineering, etc. Mainly used for optical cables with 8-12mm cable diameter. Large quantities are exported to South America, Southeast Asia and other countries and regions.Features:Dimension: 205×90×45mmUnit weight:410gCarton size: 550×410×250mmQuantity per carton : 50 piecesMaterial: Nylon and stainless steelCable diameter: 8-12mmInstallation image:
Связаться сейчас
Lock nut, self-tightening nut is a common tightening lock nut, carbon steel material, galvanized process, with high hardness, durability, long service life and other characteristics.
Связаться сейчас
1.Product name: tooth-shaped stainless steel cable tie buckle 2.Material: 316/304 stainless steel, with good and corrosion resistance.
Связаться сейчас
The strength distribution cable is equipped with rubber pads to offer anti-put on characteristic. the state line is not geared up with rubber pads and isn't sandblasted. due to the fact that there are rubber pads to provide buffering around the cord, the abrasion of the touch floor between the wire and the insulator is prevented. therefore, the energy distribution cable can provide better safety to the wires, and the installation is less difficult and faster.
Связаться сейчас
Tie rods is supplied with four full nuts. The material of the rods is steel, strength grade designation 4.6 and meet the requirements for mechanical properties.
Связаться сейчас
The hoop device is composed of a hoop plate, a wing plate, a tie rib plate, a bolt and an inner liner. An embedded hoop, which is formed by joining the left and right halves of the hoop.
Связаться сейчас
Optical cable clamps FTTH optical fiber accessories 201 stainless steel + nylon material, customized various optical cable overhead fittings, FTTH optical fiber into the home, optical fiber into the community accessories, etc.The fiber is squeezed through the sheet and the sheet, and the fiber is squeezed in the middle to complete the wiring function. The main function is to prevent the wire body from bending and protect the wire body, and the locking position can be moved quickly and simply. It is easy to use, put the optical fiber into the slot, install the pull piece, and tighten
Связаться сейчас
Steel belt 20X0.7mm with buckle, tts strength and ductility meet requirements for bending the different size of cables on poles. Steel Buckle can hold a single or double wrapped band configuration.Packing:Steel roll of 50 m is packed in form of closed reel rewind tape in nylon plastic roll.
Связаться сейчас
The surplus cable rack is used to suspend and fix the surplus OPGW optical cable and ADSS optical cable on the tower in the overhead line for maintenance and inspection. 1.The remaining cable rack for poles is fixed on the poles by two sets of steel band hoops 2. The remaining cable frame for the tower is fixed on the iron tower angle steel by two sets of right-angle splints.Purpose: It is used to place the surplus optical cable when the optical cable is connected.
Связаться сейчас
Features: 1.The product has been treated with hot-dip galvanizing and has good outdoor anti-corrosion performance. 2.According to the requirements of different optical cables, products that ensure that the optical cable is smaller than the bending radius can be designed. 3.It is convenient to install the pole and tower, the installation is firm, and the optical cable can be well protected to avoid the optical cable from wearing. Purpose: It is used to place the surplus optical cable when the optical cable is connected.
Связаться сейчас
ADSS optical cable tower with down-lead clamp, optical cable clamp, fixed optical cable clamp.The lead-down clamp is used to lead down the optical cable and fix the optical cable when it is jumpered, which improves the mechanical performance of the clamp. It is mainly used for the communication line of the newly built overhead high-voltage power transmission system of 35kv and above. The stainless steel tube and cable core stranding design is reasonable, and the optical fiber is redundant.
Связаться сейчас
The cable lugs Terminals are suitable for the connection of wires, power cables and electrical equipment in the distribution device. It is a connector that connects and protects the aluminum wire and the required connection items. It is preferably pure aluminum, which has good electrical conductivity, high temperature resistance, fast heat dissipation, galvanic corrosion resistance, and long service life.
Связаться сейчас
Eye to eye turnbuckle is composed of an adjusting rod with left and right threads, a nut and a tie rod. It uses a lead screw to expand and contract to adjust the tightness of the wire rope. In order to prevent rust, the surface treatment of turnbuckle screws: generally electroplating and hot-dip plating.1.Types: turnbuckle bolt, open body turnbuckle2.Material: Q235B steel 3.The main purpose: to adjust the tightness of the wire rope, and it is widely used.4.Features: simple structure, easy processing, low cost, and strong practicability.
Связаться сейчас
The aluminum terminal is pressed by aluminum rod, and made of punching press. It is used for the connection of distribution box, aluminum wire, aluminum cable and other wires. It is preferably pure aluminum, which has good electrical conductivity, high temperature resistance, fast heat dissipation, galvanic corrosion resistance, and long service life.
Связаться сейчас