The stay rods is for 40kN LV stays, the diameter of rods is M16, each element/material stay rod, stay base plate, guy grip, top make off, thimble are easy for assembly.A drawing of stay bows complete with thimble:
Связаться сейчас
Stay rod is used for sustaining the mechanical load of the stay wires.The stay bow are made of Q235B steel, hot dip galvanized surface treatment which used for LV & MV stay rod assembly installation. Both bow type and tubular type we can supply, the tubular type stay rods MV & LV(M16×1830mm; M20×2440mm)exported to most of African countries.Features:1. Material: high strength carbon steel2. Application: for stay rod assembly3. Dimension: 16mm4. Finish: hot dip galvanized
Связаться сейчас
The stay rod is called stay set as well, it is a component used to connect the stay wire to the ground anchor.The stay rod are made of Q235B steel, hot dip galvanized surface treatment which used for LV & MV stay rod assembly installation. Both bow type and tubular type we can supply, the tubular type stay rods MV & LV(M16×1830mm; M20×2440mm)exported to most of African countries. Features:1. Material: high strength carbon steel2. Application: for stay rod assembly3. Dimension: M20×2440mm4. Finish: hot dip galvanized
Связаться сейчас
The stay plates are made of Q235B steel, hot dip galvanized surface treatment which used for LV & MV stay rod assembly installation. Both bow type and tubular type we can supply, the tubular type stay rods MV & LV(M16×1830mm; M20×2440mm)exported to most of African countries.Features:1. Material: high strength carbon steel2. Application: for stay rod assembly3. Dimension: 450×450×6mm×22mm hole diameter4. Finish: hot dip galvanized
Связаться сейчас
Tension insulators are used for transmission and distribution lines and communication lines, broadcast line terminals, corners or large-span poles, The balance pole is subjected to tensile stress. When in use, the wire and the pull wire pass through the hole and slot, and the tension wire is used for insulation and connection.Features:1. Material: high strength carbon steel2. Application: for stay rod assembly3. Dimension: M16×1830mm4. Finish: hot dip galvanized
Связаться сейчас
Stay guy grips are used for stay rod, stay insulator and pole top attachment.
Связаться сейчас
The tie strap is used for tying 11kV or 33kV cross-arms to poles. There are steel galvanized bolts and nuts assembled. All ferrous part is made in hot dip galvanized.
Связаться сейчас
Stay grips dead ends is the preformed wire type, minimum length is 600mm and finish is galvanized. Thimbles is used with guy grips to support wires through the stay rod eye. A combination of guy grips and pole top make offs is used.Installation image:
Связаться сейчас
Galvanized steel pole top make off is generally double wrapped around the pole. 3 strands plus king wire and effective 7 strand stay length for dead end attachment. top to facilitate termination of the stay strand that firms the pole on the earth.Features:1. Material: galvanized steel wire2. Application: for stay rod assembly3. Dimension: 1750 overall length mm4. Finish: hot dip galvanized5. Stay wire diameter: 12mm6. Tensile strength” 63kNProduction drawing: Installation image:
Связаться сейчас
The second damper can be used for OPGW tension tower vibration dampers if necessary. Tension assembly is used for OPGW cable route's fixing and anchor shackling. Usually be installed on the terminal tower, tight tension tower and intersection angle tower.OPGW tension tower vibration dampers installation image:
Связаться сейчас
The galvanized steel strand is made of galvanized material and is composed of multiple steel wires. It has strong anti-rust, anti-rust ability, corrosion resistance, strong load-bearing, and good toughness. After multiple tensile tests, each steel wire rope has no breaks and no loose strands. The surface is smooth, burr-free, high tensile strength, and small bending radius.
Связаться сейчас
Features: 1. The application force has no concentrated point, the stress is uniform, and it has a good protective effect on the optical cable. 2. Under the premise of not exceeding the lateral compression strength of the optical cable, it has a greater grip on the optical cable and can withstand greater tension.
Связаться сейчас
The hook of the parallel cable clamp can be rotated and fixed at ninety degrees. It is used to fix the optical cable wire, fasten it on the steel strand, and connect and fix the S-shaped fixing member on the steel strand. The stranded stay wire is 2.0mm*7 & 2.2mm*7.Dimension : 50×31.5×80mm(L×W×H)Installation image: Drawing:
Связаться сейчас
Tension set ADSS cables installation requires a special tangent assembly or a mechanical dead end at each pole. Tension clamp helical spiral usually with several numbers of rods, such as 7 of rods and thickness of each rod can be different based on different requirements. 2.5mm is the most often cable sizes. And always be compatible with fitting accessories.Sn Model No.
Связаться сейчас
A hoop is a component that uses one material to hug or hoop another material, which is a fastener. There are many types of hoops, cable hoops, telegraph pole hoops, cable hoops, cable hoops, and stainless steel hoops are more commonly used.Technical specification table:
Связаться сейчас
The preformed dead end is used to fix the cable clamp of the cable of the tower, the iron tower, and the microwave tower. It can replace the U-T clamp and the wedge clamp that are commonly used to fix the cable on the line tower. The unique design makes the tension-resistant structure of the cable simple and reliable. After installation, the empty tube formed by the twisting of the two legs of the pre-twisted wire of the wire clip can be wound on the cable to produce a strong grip. The twisted ring is used to fix the ground anchor. Or on the tower pole.
Связаться сейчас
1. The twisting direction of the steel stranded wire and the matching preformed guy grip needs to be the same, and the tensile strength of the galvanized steel wire is 1370N/mm2-1470N/mm2. 2. The white corundum used to increase the friction between the pre-twisted wire and the surface should meet the requirements of GB/T 2479.3. The surface of the preformed guy grip should be smooth and free of defects such as cracks, folds and scars.4. The size and tolerance of the pre-twisted wire The size of the pre-twisted wire should meet the requirements of the design d
Связаться сейчас
Details and characteristics of strain clamps: 1.U shackle: hot-dip galvanized cast steel U-shaped hanging ring, which is used to connect with the pole tower fastener. 2.Insert ring: Hot-dip galvanized precision cast steel insert ring, which is embedded in the bending head of the U-shaped hanging ring of the tension clamp, which can protect the tension clamp and connect with the extension rod. 3.PD hanging plate: The hot-dip galvanized precision cast steel PD hanging plate is used to connect the embedded ring and the U-shaped hanging ring, and avoid the optical cable at the exit
Связаться сейчас
The wedge-shaped clamps for ADSS cables produced by our company are sturdy and durable, and the specifications are 12-15mm. Stainless steel wire rope and PA66 main material, injection molding process, color is black. Large quantities are sold in Africa, Southeast Asia, South America and other countries and regions. It has the advantages of convenient use, firm fixation, and reduced working hours.Features:Dimension: 245×90×45mmUnit weight:550gCarton size: 550×410×250mmQuantity per carton : 50 piecesMaterial: Nylon and stainless steelCable diameter: 12-15mmInstallation image:
Связаться сейчас
The self-supporting figure 8 optical cable clamp has a flat surface, special material and embedded design, which can well protect the cable. Its technology is superb: high-quality aluminum alloy material, rubber clamp block, reduce wear.
Связаться сейчас
The PA2000 FTTH plastic tension clamp is designed to anchor insulated service lines with 2 conductors to the pole. The clamp is composed of a body, wedges and removable, adjustable bail. One core adjustable anchor clamp are designed to supporting the neutral messenger, the wedge can be self-adjusted.Features:Unit weight:550gCarton size: 550×410×250mmQuantity per carton : 50 piecesMaterial: Nylon and stainless steelCable diameter: 12-15mmTension strength: 7KNDrawing:
Связаться сейчас
APG-A1 Aluminum Parallel M&A Clamp is suitable for the non-load-bearing splicing and branching of aluminum stranded wires and steel core aluminum stranded wires.
Связаться сейчас
The down-lead clamp for metal rods is used to fix ADSS on the rod. It is suitable for different cable diameters. It is convenient and reliable to install and has a wide adjustable range.1.Function: Fix the optical cable leading up or down on the pole tower to prevent it from shaking and avoid the optical cable from wearing. 2.Condition: The fiber optic cable line and the continuous poles on the first and end poles. 3.Method: usually install one every 1.5 meters.Technical specification table:
Связаться сейчас
ADSS spiral helical dead end consists of an anchor shackle, thimble clevis and preformed guy grip of suitable length, which used for supporting ADSS fiber optic cable in tension at cable sections, acute turnings or at the terminal pole. -Design for quick and easy installation-Minimizing time consuming civil works -Provide a future proof aerial network-Temperature: -10°C up to +70°CSn Model No. Suitable for ADSS cable range(mm) 300M spanANZ 030/0940 8.6-9.4ANZ 030/1010 9.5-10.1ANZ 030/1070 10.2-10.7ANZ 030/1140 10.8-11.4ANZ 030/1220 11.5-12.2ANZ
Связаться сейчас