Cable Stockbridge Damper for OPGW-manufacture,factory,supplier from China

(Total 24 Products for Cable Stockbridge Damper for OPGW)
The second damper can be used for OPGW tension tower vibration dampers if necessary. Tension assembly is used for OPGW cable route's fixing and anchor shackling. Usually be installed on the terminal tower, tight tension tower and intersection angle tower.OPGW tension tower vibration dampers installation image: 
  Связаться сейчас
FR anti-vibration hammer, optical cable anti-vibration hammer, pre-twisted anti-vibration hardware Product usage: Reduce the vibration amplitude of the wire. Applicable conductor: steel core aluminum stranded wire Process: Hot-dip galvanizingFeatures: 1.Tuning fork structure: The anti-vibration hammer adopts a special tuning fork structure, which can generate four resonant frequencies, which greatly covers the vibration frequency range of the cable in reality. 2.Real materials: The hammer head is gray cast iron, painted.
  Связаться сейчас
OPGW Optical Cable Tension Fitting StringFeatures:a. Even stress distribution, no stress concentration point, can well protect the optical cable.b. Under the premise of not exceeding the lateral compression strength of the optical cable, it has a greater grip on the optical cable and can withstand greater tension.c. The grip strength of the optical cable is not less than: 95% of the ultimate tensile strength (UTS) of the optical cable, which is completely suitable for the needs of optical cable erection. Schematic diagram of product composition:Technical specification sheet
  Связаться сейчас
The OPGW grounding clamp consists of a section of aluminum alloy wire, an aluminum alloy clamp (connected to the OPGW optical cable), and all-aluminum terminal blocks (connected to the main material of the iron tower).
  Связаться сейчас
The grounding clamp is mainly used for the grounding of the OPGW optical cable to provide a path for short-circuit current. The grounding clamp consists of a grounding wire, a set of aluminum alloy parallel groove clamps (connecting OPGW optical cable and grounding wire) and a terminal (connecting to the iron tower). Usually, one terminal tower and linear tower are equipped, and two connecting towers are equipped.
  Связаться сейчас
Function: the anti-vibration part dampen wind vibration, consume or weaken the vibration energy generated by the laminar wind during the operation of the optical cable, and prevent the damage of the hardware and the optical cable. Purpose: Suitable for ADSS optical cable. Factors that cause vibration: wind force, wind speed, tension, span, wind direction, topography, landform, fiber optic cable structure, length, etc. Note: The installation position of the spiral damper on the tension clamp or the suspension clamp is the same.Specification required for different cable diameter r
  Связаться сейчас
-Impact: No damage on dropping from altitude ≥ 6m to a hard floor-Vibration: Resistance against vibration of standard sine wave, frequency: 20 Hz, Amplitude: ≥ 5mm, duration: 0.5 hour-Material: durable PVC-Color: light gray or white -Temperature: -10°C up to +70°C-Humidity: Up to 100 %.Specification required for different cable diameter ranges:No.ItemUnitSpecification required for different cable diameter ranges (mm)4.0 ~ 6.346.35~ 8.288.5 ~ 11.711.71 ~ 14.314.31 ~ 19.31.1Diametermm9.8-10.39.8-10.310.8-11.312.0-12.912.0-12.91.2Length mm125012501300135016501.3Gripping section lengthmm
  Связаться сейчас
Features: 1.Tuning fork structure: The anti-vibration hammer adopts a special tuning fork structure, which can generate four resonant frequencies, which greatly covers the vibration frequency range of the cable in reality. 2.Real materials: The hammer head is gray cast iron, painted. Anti-oxidation, corrosion resistance and long service life. 3.Various types of anti-vibration hammers: You can choose freely according to your needs.The anti-vibration hammer is designed to reduce the vibration of the wire due to wind.
  Связаться сейчас
Applications 1.Tensile clamps for OPGW optical cables are mainly used to connect optical cables with a breaking strength of 160kN and below to tensile poles, corner poles and terminal poles. The complete set of OPGW optical cable strain clamp includes outer pre-twisted wires, inner pre-twisted wires, supporting connectors and grounding wires.
  Связаться сейчас
Power equipment optical cable communication 4D type protective hardware anti-vibration hammer with armor rod. Features: Due to the use of hammers with different sizes and masses, the response frequency range of traditional shock-proof hammers is expanded. Because the shapes of large and small hammers and hooks have no edges and corners, corona is reduced. In addition, the use of aluminum alloy for the hook can also reduce the energy loss of the wire.
  Связаться сейчас
Suspension string fittings include U-shaped screws, suspension clamps, pre-twisted wire protection lines, grounding drain wires and necessary connection fittings. The mechanical strength of the hanging string connection fittings is 70kN. The suspension clamp is a pre-twisted wire type, and the clamp body is made of aluminum alloy. The clamp body should be equipped with an EPDM rubber cushioning elastic pad. The allowable value of the drape angle at the outlet of the OPGW single drape clamp is not less than 15 degrees.
  Связаться сейчас
The surplus cable rack is used to suspend and fix the surplus OPGW optical cable and ADSS optical cable on the tower in the overhead line for maintenance and inspection. 1.The remaining cable rack for poles is fixed on the poles by two sets of steel band hoops 2. The remaining cable frame for the tower is fixed on the iron tower angle steel by two sets of right-angle splints.Purpose: It is used to place the surplus optical cable when the optical cable is connected.
  Связаться сейчас
ADSS spiral vibration rods is mainly used on overhead lines to eliminate or reduce the vibration of wires and optical cables under the action of laminar wind to clamp the damage to the fittings and the outer sheath of the optical cable. The anti-vibration whip is not only suitable for ADSS optical cables, but also suitable for OPGW optical cables and power transmission cables.Structural features: 1. The structure is simple, the installation is convenient, the maintenance is easy, and the installation position is not limited. 2. The spiral vibration isolator includ
  Связаться сейчас
Material 1. Rubber Clamps Composed of high-quality rubber and center reinforcement, it has the properties of ozone resistance, chemical resistance, weather resistance, high and low temperature performance, high strength and elasticity, and small compression deformation. 2. Aluminum splint It is made of corrosion-resistant aluminum alloy by pressure casting. The aluminum alloy has stable chemical properties, good atmospheric corrosion resistance and good mechanical properties.
  Связаться сейчас
Power Fittings FFH Optical Cable Shockproof Hammer Product usage: Reduce the vibration amplitude of the wire. Applicable conductor: steel core aluminum stranded wire Process: alloy aluminum Features: 1.Tuning fork structure: The anti-vibration hammer adopts a special tuning fork structure, which can generate four resonant frequencies, which greatly covers the vibration frequency range of the cable in reality. 2.Real materials: The hammer head is gray cast iron, painted.
  Связаться сейчас
The wire clamp is composed of a rubber clamp block, a pre-twisted wire and a cast aluminum casing. 1. Enhance the rigidity of the cable hanging point and increase the radius of curvature. The single-line clamp can meet the 30° steering angle, and the double-line clamp can meet the 60° steering angle. 2. It can be ensured that the cable is not subject to large bending stress near the outlet of the wire clamp, so as to avoid local mechanical damage causing strand break or wire breakage.
  Связаться сейчас
Features: 1.The product has been treated with hot-dip galvanizing and has good outdoor anti-corrosion performance. 2.According to the requirements of different optical cables, products that ensure that the optical cable is smaller than the bending radius can be designed. 3.It is convenient to install the pole and tower, the installation is firm, and the optical cable can be well protected to avoid the optical cable from wearing. Purpose: It is used to place the surplus optical cable when the optical cable is connected.
  Связаться сейчас
Hot-rolled steel strip or steel plate is used as raw material and rolled into a product by a cold rolling mill at room temperature.1.Standard: GB4239-84 2.Features: good surface quality and smooth 3.Billet: Hot-rolled stainless steel strip4.The thickness of cold-rolled steel strip is 0.1~3mm, such as: 0.30, 0.40, 0.50, 0.60, 0.70, 0.80, 0.90, 1.00, 1.20, 1.50, 2.00, 2.50, 3.00mm.The surplus cable rack is used to suspend and fix the surplus OPGW optical cable and ADSS optical cable on the tower in the overhead line for maintenance and inspection. 1.The remaining cable rack for po
  Связаться сейчас
The cable tie is able to loop and lock fully. Extra tie material left past the lock to prevent pull through. Self-locking design for fast and secure installation provided.The cable tie have maximum diameter capable of bundling two to four service wires and cables with cross-section in the range of 4-25mm2. 
  Связаться сейчас
Preformed inner protection line rods:The material is aluminum-clad steel wire, which is the same material as all the aluminum-clad steel wires of OPPC cable. The inner wall of the protector rods is glued with a layer of gold steel sand through a high-strength polymer water-soluble environmentally friendly adhesive to increase the friction with the optical cable. The rods is preformed into four sub-bundles during production, which is convenient for quick installation.
  Связаться сейчас
Features: a. Even stress distribution, no stress concentration point, can well protect the optical cable. b. Under the premise of not exceeding the lateral compression strength of the optical cable, it has a greater grip on the optical cable and can withstand greater tension. c. The grip strength of the optical cable is not less than: 95% of the ultimate tensile strength (UTS) of the optical cable, which is fully suitable for the needs of optical cable erectionProduct composition diagramProduct technical specification sheet:  Sn Model No.
  Связаться сейчас
Features: 1. It has all the functions of a single suspension clamp.2.
  Связаться сейчас
ADSS optical cable suspension clamps are divided into several types according to the size of the line span, such as single-layer pre-twisted wire tangent clamps, single suspension clamps and double suspension clamps. The tangent clamp for ADSS optical cable is mainly used for the cable erection of 100m span, and the single-layer pre-twisted wire suspension clamp is mainly used for the erection of optical cable within the span of 100m-200m.Features: a. The suspension clamp has a larger contact area with the ADSS/OPGW optical cable, the stress is evenly distributed, and there is n
  Связаться сейчас
Features: 1. The application force has no concentrated point, the stress is uniform, and it has a good protective effect on the optical cable. 2. Under the premise of not exceeding the lateral compression strength of the optical cable, it has a greater grip on the optical cable and can withstand greater tension.
  Связаться сейчас
Relate News
Features of Transmission Line OPGW Tension SetA. the stress distribution is uniform and there can be no pressure focus factor, that can protect the optical cable well.B. beneath the concept of now not exceeding the lateral compression electricity of the optical cable, it has a greater grip at the optical cable and can resist more tension.C. the grip energy of the optical cable isn't always much less than: 90 5% of the last tensile energy (uts) of the optical cable, that is clearly suitable for the wishes of optical cable erection.
Wonderful anti-pressure ability, accurate brief-circuit current ability ;Match with ordinary floor cord l undertake stainless-steel pipe production generation, the pipe is full of water-blocking off compounds, the application version can efficaciously protect the optical fiber ;Using stainless steel tube production technology, the tube filled with water-blocking compounds, can effectively protect the optical fiber;The utility model has the dual functions of a ground wire and a communication optical cable, and avoids the huge cost of repeated erection and maintenance;It is installed on the top
Wires mainly include bare wires, electromagnetic wires, insulated wires, power cables, communication cables and optical cables for electrical appliances. Electric cable refers to the materials used for power, communication and related transmission purposes. There is no strict boundary between "wire" and "cable".
Optical cable joint box, ADSS optical cable joint box, OPGW optical cable joint box, OPPC optical cable joint box Uses: Widely used in ADSS, OPGW special optical cable joints and the junction of different optical cables, and play a role in protecting optical cable joints. Features: 1.The metal splice box is made of aluminum alloy casting, which is especially suitable for the protection of optical cable joints under high-voltage electric fields. 2.The metal splice box overcomes the weakness of the plastic splice box, which is poor in anti-aging ability and short life under t
Tools/raw materials Aluminum alloy joint box Pre-twisted suspension clamp Optical cable down lead clamp Cable rack Tower fastener Cable hoop Whip and hammer Pre-twisted hardware1.Before installing the inner twisted wire, pass the outer twisted wire through the embedded ring and make it parallel to the optical cable, and mark the optical cable where the outer twisted wire is colored.2.Winding the first group of inner twisted wires on the optical cable; Align the second group of inner twisted wires with the first group of inner twisted wires, winding the s
The preformed suspension clamp is used for the connection of various wires such as ADSS optical cable and OPGW optical cable in the linear pole tower.
Characteristics of PET Packing Tape(1) Sturdy tensile energy, not most effective has the tensile power of metal strip, but additionally has the ductility of effect resistance, that may ensure the transportation safety of merchandise. (2) Small elongation, elongation is most effective one-sixth of the polypropylene belt, can hold the anxiety for a long time. (3)Robust temperature resistance, melting point of 260 stages, a hundred and twenty degrees under the use of non-deformation. (4) Top security, no metal rust pollutants of the sure gadgets, vivid shade can be used for referen
1.1 puncture structure, easy installation, no need to peel insulated wire; 1.2 moment nut, constant puncture pressure, ensure good electrical connection without damaging wire; 1.3 self sealing structure, moisture proof, water proof, corrosion proof, extend The service life of insulated conductors and clamps 1.4 use special contact blade, suitable for copper (aluminum) Butt joint and copper-aluminum transition 1.5 electrical contact resistance is small, contact resistance is less than 1.1 times of resistance of equal length branch wire, dL/T765.1-2001 standard 1.6 speci
Power fittings are accessories made of metal materials that are often used for power output. These accessories are of various types, and the shape and size of each part are different, but they play a very important role. Even very small parts will be indispensable, helping people to output electricity. Some of our common metal rings or metal clips, as well as connecting rings that can be connected to metal pipes, belong to the category of fittings.
With the continuous growth of China's national economy as a whole and the influence of the reform of telecommunications system, the market demand for ADSS power optical cable has increased significantly, reaching 10 million core kilometers in 2001.In the 21st century, there were several situations at that time: (1) Domestic optical cable enterprises were affected by the "bubble" of optical network, and the telecom market shrank, and the supply exceeded demand.
1.extensive variety of applications, torsion resistance and pressure resistance, balanced torsion torque, company and tight locking, and huge adjustment variety. 2.put it at the telegraph pole, tighten and fix it. 3. the poles with diameters of one hundred seventy five-197mm can be adjusted. Pole clamp belt for cable garage bracket is manufactured from c201 stainless-steel, with width of 19mm, thickness of 0.7mm and duration from 1.2m to at least one.5m primarily based on exclusive pole.
A guided wave structure that transmits electrical energy and/or electrical signals in the form of transverse electromagnetic (TEM) modes. The characteristic of transmission line is that its transverse dimension is much smaller than the working wavelength. The main structural types are parallel double-wire, parallel multi-wire, coaxial line, stripline, and microstrip line working in quasi-TEM mode (Fig. 1)(see telecommunication cable) , which can be analyzed by simple double-wire model.