Helical tension set ADSS long span with D shackle, Thimble clevis, helical dead end, protector rods. A dead-end is installed at each end of the cable length to attach to the structures. Two dead ends are used at angle changes of 30 degree or greater, either horizontal or vertical.
Связаться сейчас
Product advantages: 1. There is a large contact area between the clamp and the pull wire, the stress distribution is even, there is no stress concentration point, and the achievable grip strength is not less than 95% of the stranded wire Calculate the breaking force. 2. The dead end preformed guy grip is made of the same material as the pull wire, which has good corrosion resistance. 3. The dead end preformed guy grip is simple to install, without any special tools, and can be done independently by one person.
Связаться сейчас
ADSS spiral helical dead end consists of an anchor shackle, thimble clevis and preformed guy grip of suitable length, which used for supporting ADSS fiber optic cable in tension at cable sections, acute turnings or at the terminal pole. -Design for quick and easy installation-Minimizing time consuming civil works -Provide a future proof aerial network-Temperature: -10°C up to +70°CSn Model No. Suitable for ADSS cable range(mm) 300M spanANZ 030/0940 8.6-9.4ANZ 030/1010 9.5-10.1ANZ 030/1070 10.2-10.7ANZ 030/1140 10.8-11.4ANZ 030/1220 11.5-12.2ANZ
Связаться сейчас
ADSS terminating helix dead end is made of aluminum-clad steel wire, and the pre-twisted wire is preformed into a bundle during processing, and a firm layer of emery is glued to the inner wall to increase the grip of the tension clamp under the condition of reducing the side pressure on the optical cable.
Связаться сейчас
Dead end clamp is made of plastic body with very high mechanical and climatic resistance. A stainless steel flexible cord equipped with movable insulating saddle and two sleeves compressed on the ends to prevent detachment from the clamp body.An inner sheath consisting of two insulating plastic wedges for clamping of the neutral carrier without damaging the cable insulation.
Связаться сейчас
ADSS spiral helical dead end consists of an anchor shackle, thimble clevis and preformed guy grip of suitable length, which used for supporting ADSS fiber optic cable in tension at cable sections, acute turnings or at the terminal pole. -Design for quick and easy installation-Minimizing time consuming civil works -Provide a future proof aerial network-Temperature: -10°C up to +70°CSn Model No. Suitable for ADSS cable range(mm) 300M spanANZ 030/0940 8.6-9.4ANZ 030/1010 9.5-10.1ANZ 030/1070 10.2-10.7ANZ 030/1140 10.8-11.4ANZ 030/1220 11.5-12.2ANZ
Связаться сейчас
The preformed helical guy grip clamp for the conductor is hooked up to the tower by means of its matching fittings, along with insert ring, bowl-head striking plate, and so forth., that could replace conventional bolt-type tension clamps, compression-type anxiety clamps and wedge-type anxiety cables folder.Structure composition and material description 1. Non-twisted ring: standard form, suitable for small diameter wires; Stranded ring: suitable for larger diameter wires 2. Color code: starting mark of installation 3. Label: Indicate the product model 4. Pre-twisted wi
Связаться сейчас
Tension set ADSS cables installation requires a special tangent assembly or a mechanical dead end at each pole. Tension clamp helical spiral usually with several numbers of rods, such as 7 of rods and thickness of each rod can be different based on different requirements. 2.5mm is the most often cable sizes. And always be compatible with fitting accessories.Sn Model No.
Связаться сейчас
ADSS spiral vibration rods is mainly used on overhead lines to eliminate or reduce the vibration of wires and optical cables under the action of laminar wind to clamp the damage to the fittings and the outer sheath of the optical cable. The anti-vibration whip is not only suitable for ADSS optical cables, but also suitable for OPGW optical cables and power transmission cables.Structural features: 1. The structure is simple, the installation is convenient, the maintenance is easy, and the installation position is not limited. 2. The spiral vibration isolator includ
Связаться сейчас
The top tie are all designed in a spiral structure and include aluminum-clad steel wires. the central part of the energy distribution cable is fashioned in the factory, and its form may be matched with diverse insulators and wires.
Связаться сейчас
Preformed helical guy grip clamp with long span helical dead end, thimble clevis, U shackle, link fitting and pole attachment with related accessories.
Связаться сейчас
1.The short span ADSS helical guy grip is used for 10.6-11.6mm ADSS cable, with approximate length 940mm±30mm, or customize based on requirements of customers.2.The structure of the short span ADSS guy grip is simple installation, with strong grip once the tubular structure naturally wound on the ADSS cable. 3.The short span ADSS helical guy grip has reliable performance, made of aluminum-clad steel.Using tips1.Due to the special structure of guy grip, only be used once after being stressed, and cannot be reused. 2.The specification and model of the guy grip must be provided when an
Связаться сейчас
Structural features: 1.The anti-vibration rod will not cause the stress concentration of the wire, nor damage the wire, to avoid corrosion or arcing. 2.The spiral anti-vibration rod is composed of a short gripping section and a long damping section. 3.The gripping section can effectively hold the cable and firmly fix it on the cable.
Связаться сейчас
ADSS preformed tension clamp needs to know the outer diameter and force value of the optical cable to request a quotation.
Связаться сейчас
The preformed tension clamp for the conductor is connected to the tower by its matching fittings, such as insert ring, bowl-head hanging plate, etc., which can replace conventional bolt-type tension clamps, compression-type tension clamps and wedge-type tension cables folder.Structure composition and material description 1. Non-twisted ring: standard form, suitable for small diameter wires; Stranded ring: suitable for larger diameter wires 2. Color code: starting mark of installation 3. Label: Indicate the product model 4. Pre-twisted wire: aluminum-clad stee
Связаться сейчас
Galvanized steel thimble clevis is compatible with dead end application to attach loop type dead end to tongue or eye type fittings. It is usually ductile iron material, hot dip galvanized and with 5/8” dia clevis pin.
Связаться сейчас
ADSS optical cable suspension clamps are used for the suspension and support of optical cables on straight poles.
Связаться сейчас
The energy distribution top tie can be used to fix naked or insulated wires inside the top grooves of pin insulators and submit insulators of the power distribution device.
Связаться сейчас
Fiber optic tangent used as cable suspension hardware simplest while the attitude of change, ether horizontal or vertical, is less than 15°.Armor grip suspesnion used for any span length with an angle change, either horizontal or vertical, less than 30°. Adss optical cable small pitch suspension clamps are especially used for cable erection within 100m pitch, and single-layer pre-twisted cord suspension clamps are specially used for optical cable erection inside 100m~200m pitch.
Связаться сейчас
-Impact: No damage on dropping from altitude ≥ 6m to a hard floor-Vibration: Resistance against vibration of standard sine wave, frequency: 20 Hz, Amplitude: ≥ 5mm, duration: 0.5 hour-Material: durable PVC-Color: light gray or white -Temperature: -10°C up to +70°C-Humidity: Up to 100 %.Specification required for different cable diameter ranges:No.ItemUnitSpecification required for different cable diameter ranges (mm)4.0 ~ 6.346.35~ 8.288.5 ~ 11.711.71 ~ 14.314.31 ~ 19.31.1Diametermm9.8-10.39.8-10.310.8-11.312.0-12.912.0-12.91.2Length mm125012501300135016501.3Gripping section lengthmm
Связаться сейчас
The preformed dead end is used to fix the cable clamp of the cable of the tower, the iron tower, and the microwave tower. It can replace the U-T clamp and the wedge clamp that are commonly used to fix the cable on the line tower. The unique design makes the tension-resistant structure of the cable simple and reliable. After installation, the empty tube formed by the twisting of the two legs of the pre-twisted wire of the wire clip can be wound on the cable to produce a strong grip. The twisted ring is used to fix the ground anchor. Or on the tower pole.
Связаться сейчас
The thimble clevis is mainly for ADSS light span tension set which made of galvanized ductile iron.All dielectric dead-ends require a proper size and strength thimble clevis or extension link.Technical characteristics:Model No.: TC-02Associated Bolt size: M14Tension strength: 20KNFinish: hot dip galvanized steelCotter pin: stainless steelDrawing: Installation image(part 2):
Связаться сейчас
ADSS optical cable small tension strain clamp, single-layer twisted wire can be used below 200 meters; high-tension strain clamp, double-layer twisted wire can be used for spans above 200 meters. The technical parameters required for the quotation are: the diameter of the applied wire, the range of use, the tensile force and so on.Preformed tension set usually used for feeder and distribution ADSS cables installation.
Связаться сейчас
Features: 1.High mechanical strength. 2.Aluminum alloy material, rust proof and waterproof. 3.Spiral design anti corona. Anti-corona ring for ADSS is made of Al. Alloy. 1.Select the required model according to the diameter of the optical cable. 2.Each set of strain clamp is equipped with an anti-corona ring.The ADSS optical cable erected on the same pole with the high-voltage overhead transmission line is prone to electrical corrosion at the outlet of the fittings.
Связаться сейчас