ADSS Spiral Vibration Rods-manufacture,factory,supplier from China

Features: 1.Tuning fork structure: The anti-vibration hammer adopts a special tuning fork structure, which can generate four resonant frequencies, which greatly covers the vibration frequency range of the cable in reality. 2.Real materials: The hammer head is gray cast iron, painted. Anti-oxidation, corrosion resistance and long service life. 3.Various types of anti-vibration hammers: You can choose freely according to your needs.The anti-vibration hammer is designed to reduce the vibration of the wire due to wind.

ADSS spiral vibration rods is mainly used on overhead lines to eliminate or reduce the vibration of wires and optical cables under the action of laminar wind to clamp the damage to the fittings and the outer sheath of the optical cable. The anti-vibration whip is not only suitable for ADSS optical cables, but also suitable for OPGW optical cables and power transmission cables.Structural features: 1. The structure is simple, the installation is convenient, the maintenance is easy, and the installation position is not limited. 2. The spiral vibration isolator includ

-Impact: No damage on dropping from altitude ≥ 6m to a hard floor-Vibration: Resistance against vibration of standard sine wave, frequency: 20 Hz, Amplitude: ≥ 5mm, duration: 0.5 hour-Material: durable PVC-Color: light gray or white -Temperature: -10°C up to +70°C-Humidity: Up to 100 %.Specification required for different cable diameter ranges:No.ItemUnitSpecification required for different cable diameter ranges (mm)4.0 ~ 6.346.35~ 8.288.5 ~ 11.711.71 ~ 14.314.31 ~ 19.31.1Diametermm9.8-10.39.8-10.310.8-11.312.0-12.912.0-12.91.2Length mm125012501300135016501.3Gripping section lengthmm

Structural features: 1.The anti-vibration rod will not cause the stress concentration of the wire, nor damage the wire, to avoid corrosion or arcing. 2.The spiral anti-vibration rod is composed of a short gripping section and a long damping section. 3.The gripping section can effectively hold the cable and firmly fix it on the cable.

FR anti-vibration hammer, optical cable anti-vibration hammer, pre-twisted anti-vibration hardware Product usage: Reduce the vibration amplitude of the wire. Applicable conductor: steel core aluminum stranded wire Process: Hot-dip galvanizingFeatures: 1.Tuning fork structure: The anti-vibration hammer adopts a special tuning fork structure, which can generate four resonant frequencies, which greatly covers the vibration frequency range of the cable in reality. 2.Real materials: The hammer head is gray cast iron, painted.

Power Fittings FFH Optical Cable Shockproof Hammer Product usage: Reduce the vibration amplitude of the wire. Applicable conductor: steel core aluminum stranded wire Process: alloy aluminum Features: 1.Tuning fork structure: The anti-vibration hammer adopts a special tuning fork structure, which can generate four resonant frequencies, which greatly covers the vibration frequency range of the cable in reality. 2.Real materials: The hammer head is gray cast iron, painted.

ADSS/OPGW anti-vibration hammer protective wire is a protective wire used to suppress the vibration of conductors and ground wires on overhead power lines.

Function: the anti-vibration part dampen wind vibration, consume or weaken the vibration energy generated by the laminar wind during the operation of the optical cable, and prevent the damage of the hardware and the optical cable. Purpose: Suitable for ADSS optical cable. Factors that cause vibration: wind force, wind speed, tension, span, wind direction, topography, landform, fiber optic cable structure, length, etc. Note: The installation position of the spiral damper on the tension clamp or the suspension clamp is the same.Specification required for different cable diameter r

The second damper can be used for OPGW tension tower vibration dampers if necessary. Tension assembly is used for OPGW cable route's fixing and anchor shackling. Usually be installed on the terminal tower, tight tension tower and intersection angle tower.OPGW tension tower vibration dampers installation image: 

The protective wire can avoid damage caused by the aluminum clamp of the anti-vibration hammer directly clamped on the 0PGW optical cable, and has a good protective effect on the optical cable. The factors that cause vibration include span, tension, wind speed, wind direction, ground wire and cable structure size, etc. Features: a. Using a unique design, its basic principle is to dynamically absorb energy, its frequency coverage is 6Hz-150Hz, and there are four resonance frequencies in this range, which can meet the needs of various types of OPGW, and has a very effective v

Uses: Used to connect the ADSS optical cable and the pole tower in the ADSS optical cable line erection. The pre-twisted wire protects the ADSS optical cable and improves the anti-vibration effect.

Tension set ADSS cables installation requires a special tangent assembly or a mechanical dead end at each pole. Tension clamp helical spiral usually with several numbers of rods, such as 7 of rods and thickness of each rod can be different based on different requirements. 2.5mm is the most often cable sizes. And always be compatible with fitting accessories.Sn Model No.

ADSS optical cable suspension clamps are used for the suspension and support of optical cables on straight poles.

Power equipment optical cable communication 4D type protective hardware anti-vibration hammer with armor rod. Features: Due to the use of hammers with different sizes and masses, the response frequency range of traditional shock-proof hammers is expanded. Because the shapes of large and small hammers and hooks have no edges and corners, corona is reduced. In addition, the use of aluminum alloy for the hook can also reduce the energy loss of the wire.

Fiber optic tangent used as cable suspension hardware simplest while the attitude of change, ether horizontal or vertical, is less than 15°.Armor grip suspesnion used for any span length with an angle change, either horizontal or vertical, less than 30°. Adss optical cable small pitch suspension clamps are especially used for cable erection within 100m pitch, and single-layer pre-twisted cord suspension clamps are specially used for optical cable erection inside 100m~200m pitch.

The preformed armor rod is used to protect the wire from vibration, clamping stress, friction, arc and all other external damage. The armor rod section protection wire can protect the wire from arc, friction or other damage on the short-span line when the wire vibration is not serious.

ADSS spiral helical dead end consists of an anchor shackle, thimble clevis and preformed guy grip of suitable length, which used for supporting ADSS fiber optic cable in tension at cable sections, acute turnings or at the terminal pole. -Design for quick and easy installation-Minimizing time consuming civil works -Provide a future proof aerial network-Temperature: -10°C up to +70°CSn Model No. Suitable for ADSS cable range(mm) 300M spanANZ 030/0940 8.6-9.4ANZ 030/1010 9.5-10.1ANZ 030/1070 10.2-10.7ANZ 030/1140 10.8-11.4ANZ 030/1220 11.5-12.2ANZ

Features: 1.High mechanical strength. 2.Aluminum alloy material, rust proof and waterproof. 3.Spiral design anti corona. Anti-corona ring for ADSS is made of Al. Alloy. 1.Select the required model according to the diameter of the optical cable. 2.Each set of strain clamp is equipped with an anti-corona ring.The ADSS optical cable erected on the same pole with the high-voltage overhead transmission line is prone to electrical corrosion at the outlet of the fittings.

The protective armor rod is a metal wire that is spirally wound on the wire to increase the rigidity and vibration resistance of the wire at the winding position.

The preformed top tie are all designed in a spiral structure and consist of two aluminum-clad steel wires. The central part of the power distribution cable is formed in the factory, and its shape can be matched with various insulators and wires.

Medium and large tension set are composed of a double-layer twisted wire structure. The tension inner rods is made of galvanized steel wire or aluminum-clad steel wire, and the inner wall of the pre-stranded wire is stuck with a layer of fine emery to increase friction. The inner rods includes 4 groups, during processing in the factory to avoid installation errors and facilitate quick installation. The ends of the pre-twisted wires are bent radially outward to avoid squeezing and damaging the optical cable.

Tie rods is supplied with four full nuts. The material of the rods is steel, strength grade designation 4.6 and meet the requirements for mechanical properties.

The top tie are all designed in a spiral structure and include aluminum-clad steel wires. the central part of the energy distribution cable is fashioned in the factory, and its form may be matched with diverse insulators and wires.

Preformed inner protection line rods:The material is aluminum-clad steel wire, which is the same material as all the aluminum-clad steel wires of OPPC cable. The inner wall of the protector rods is glued with a layer of gold steel sand through a high-strength polymer water-soluble environmentally friendly adhesive to increase the friction with the optical cable. The rods is preformed into four sub-bundles during production, which is convenient for quick installation.