Stay grips dead ends is the preformed wire type, minimum length is 600mm and finish is galvanized. Thimbles is used with guy grips to support wires through the stay rod eye. A combination of guy grips and pole top make offs is used.Installation image:
Связаться сейчас
Dead end clamp is made of plastic body with very high mechanical and climatic resistance. A stainless steel flexible cord equipped with movable insulating saddle and two sleeves compressed on the ends to prevent detachment from the clamp body.An inner sheath consisting of two insulating plastic wedges for clamping of the neutral carrier without damaging the cable insulation.
Связаться сейчас
Galvanized steel pole top make off is generally double wrapped around the pole. 3 strands plus king wire and effective 7 strand stay length for dead end attachment. top to facilitate termination of the stay strand that firms the pole on the earth.Features:1. Material: galvanized steel wire2. Application: for stay rod assembly3. Dimension: 1750 overall length mm4. Finish: hot dip galvanized5. Stay wire diameter: 12mm6. Tensile strength” 63kNProduction drawing: Installation image:
Связаться сейчас
Helical tension set ADSS long span with D shackle, Thimble clevis, helical dead end, protector rods. A dead-end is installed at each end of the cable length to attach to the structures. Two dead ends are used at angle changes of 30 degree or greater, either horizontal or vertical.
Связаться сейчас
Square curved washer with 7/8" diameter hole for 3/4" diameter bolt. Galvanized per ASTM A-153.Features:1. Material: steel2. Finish: galvanized3. Usage: for bolts. Technical specification:
Связаться сейчас
Square flat washer with 17.5mm diameter hole for 5/8" diameter bolt. Galvanized per ASTM A-153.Features:1. Material: steel2. Finish: galvanized3. Usage: for 5/8” bolts. Technical specification:
Связаться сейчас
Product advantages: 1. There is a large contact area between the clamp and the pull wire, the stress distribution is even, there is no stress concentration point, and the achievable grip strength is not less than 95% of the stranded wire Calculate the breaking force. 2. The dead end preformed guy grip is made of the same material as the pull wire, which has good corrosion resistance. 3. The dead end preformed guy grip is simple to install, without any special tools, and can be done independently by one person.
Связаться сейчас
Grade 8.8 black finish high strength nuts are made of carbon steel, with high hardness and good wear resistance; surface treatment is black, smooth and complete, the surface is smooth without burrs, and the pattern is evenly distributed; the thread is complete, the turnbuckle is deep, and the force is uniform and not easy to be silky , It is not easy to slip and lock during rotation.
Связаться сейчас
The thimble clevis is mainly for ADSS light span tension set which made of galvanized ductile iron.All dielectric dead-ends require a proper size and strength thimble clevis or extension link.Technical characteristics:Model No.: TC-02Associated Bolt size: M14Tension strength: 20KNFinish: hot dip galvanized steelCotter pin: stainless steelDrawing: Installation image(part 2):
Связаться сейчас
PD extension clevis are mostly made of medium-thick steel by stamping and cutting processes.There are two mounting holes at both ends, hot dip galvanization with strong corrosion resistance.
Связаться сейчас
ADSS terminating helix dead end is made of aluminum-clad steel wire, and the pre-twisted wire is preformed into a bundle during processing, and a firm layer of emery is glued to the inner wall to increase the grip of the tension clamp under the condition of reducing the side pressure on the optical cable.
Связаться сейчас
The medium and high tension strain clamps are composed of a double-layer twisted wire structure. The tensile inner twisted wire is made of galvanized steel wire or aluminum-clad steel wire. The inner wall of the pre-twisted wire is stuck with a layer of fine emery to increase friction. The pre-twisted wire is preformed into four sub-bundles during processing to avoid installation errors and facilitate quick installation. The ends of the pre-twisted wires are bent radially outward to avoid squeezing and damaging the optical cable.
Связаться сейчас
Galvanized steel thimble clevis is compatible with dead end application to attach loop type dead end to tongue or eye type fittings. It is usually ductile iron material, hot dip galvanized and with 5/8” dia clevis pin.
Связаться сейчас
M16 eye nut is made of carbon steel hot-dip galvanized material, with a smooth surface, which can resist corrosion and rust in a humid environment. Solid design, thick material, durable and long service life. The internal thread is deep, the force is even, the screw teeth are sharper, and it is not easy to slip during the rotation.
Связаться сейчас
The hook of the parallel cable clamp can be rotated and fixed at ninety degrees. It is used to fix the optical cable wire, fasten it on the steel strand, and connect and fix the S-shaped fixing member on the steel strand. The stranded stay wire is 2.0mm*7 & 2.2mm*7.Dimension : 50×31.5×80mm(L×W×H)Installation image: Drawing:
Связаться сейчас
Lag screw made of forged steel have a hot dipped galvanized finish with one square nut, excellent tensile properties, good resistance to oxidation and corrosive agents. Material: carbon steelFinish: hot dip galvanized ASTM A153Standard: IEEC-135.1
Связаться сейчас
The self-supporting figure 8 optical cable clamp has a flat surface, special material and embedded design, which can well protect the cable. Its technology is superb: high-quality aluminum alloy material, rubber clamp block, reduce wear.
Связаться сейчас
Tension set ADSS cables installation requires a special tangent assembly or a mechanical dead end at each pole. Tension clamp helical spiral usually with several numbers of rods, such as 7 of rods and thickness of each rod can be different based on different requirements. 2.5mm is the most often cable sizes. And always be compatible with fitting accessories.Sn Model No.
Связаться сейчас
The preformed dead end is used to fix the cable clamp of the cable of the tower, the iron tower, and the microwave tower. It can replace the U-T clamp and the wedge clamp that are commonly used to fix the cable on the line tower. The unique design makes the tension-resistant structure of the cable simple and reliable. After installation, the empty tube formed by the twisting of the two legs of the pre-twisted wire of the wire clip can be wound on the cable to produce a strong grip. The twisted ring is used to fix the ground anchor. Or on the tower pole.
Связаться сейчас
Dimensions:Height: 545±5mm.Min Dry Aring Distance:350mm. Min Creepage Distance:900mmDiameter Of The Rod:Φ17mm.Coupling Dimensions: Single Ear/ Binaural.Number Of Sheds: 8. Raw Materials:1.End-Fitting:1.1Material: Socket: Cast Iron Or Cast Steel, Hot Dip Galvanized. Ball: Forged Steel, Hot Dip Galvanized.1.2 Minimum Thickness Of The Galvanization:86um.2.Core:2.1 Material: Epoxy& Glass Fiber, Acid-Resistant Type.2.2 Diamter:Φ17mm.3.
Связаться сейчас
Wire tension clamp NL-50/8 for steel core aluminum stranded wire made of galvanized steel wire or alloy clad steel wire. 1. The preformed guy grip is used for the installation of ACSR conductors. The product is with much more reliability and economy compared with the bolt-type & hydraulic strain clamps. 2. The structure of the preformed guy grip is simple. When installation, the tubular structure formed by the legs of the pre-twisted wire can be naturally wound on the conductor to produce a strong grip.
Связаться сейчас
Self-supporting optical cable clamp ADSS optical cable tension clamp is a commonly used ADSS optical cable clamp. The main body material is PA66, stainless steel wire rope, injection molding process, widely used in communication engineering, etc. Mainly used for optical cables with 8-12mm cable diameter. Large quantities are exported to South America, Southeast Asia and other countries and regions.Features:Dimension: 205×90×45mmUnit weight:410gCarton size: 550×410×250mmQuantity per carton : 50 piecesMaterial: Nylon and stainless steelCable diameter: 8-12mmInstallation image:
Связаться сейчас
UPB optical cable suspension bracket is a common product for FTTH accessories. The material is aluminum. It is suitable for communication optical fiber engineering dedicated to No. 8 optical cable. It is exported to South America, Southeast Asia, North America, the Middle East and other countries and regions.Features: Dimension: 120×113×45mmUnit weight:210gCarton size: 420×280×230mmQuantity per carton : 50 piecesMaterial: alloyDimension image: Packing image:
Связаться сейчас
ADSS spiral helical dead end consists of an anchor shackle, thimble clevis and preformed guy grip of suitable length, which used for supporting ADSS fiber optic cable in tension at cable sections, acute turnings or at the terminal pole. -Design for quick and easy installation-Minimizing time consuming civil works -Provide a future proof aerial network-Temperature: -10°C up to +70°CSn Model No. Suitable for ADSS cable range(mm) 300M spanANZ 030/0940 8.6-9.4ANZ 030/1010 9.5-10.1ANZ 030/1070 10.2-10.7ANZ 030/1140 10.8-11.4ANZ 030/1220 11.5-12.2ANZ
Связаться сейчас